ao link
Filter content by area of interest
Amps
Boost and Overdrive
Delay
Distortion
Fuzz
Guitars
Modulation
Pitch
Reverb
Utility
All
All

Hagerman's new Vulture Skull Tube Overdrive uses a Vintage NOS TV 1/2 Triode, 1/2 Pentode Tube to fantastic effect for a beautifully rich and expansive soundstage

BoostBoost and OverdriveHagerman AmplificationOverdrivePreAmpTube Overdrive+-
Share to TwitterShare to Facebook
2026-GPX-Hagerman-Vulture-Skull-Main-700.jpg

The Vulture Skull is a beautifully textured expansive mid-gain Tube Overdrive, which uses a pretty unique Vintage Nos Tube - which has a Triode stage as its first half, and a Pentode Clipping Stage as its second half - essentially a dual stage tube - which 2 halves can be targeted by the separate footswitches - albeit in an additive rather than independent manner. Hence why those two switches are labelled Bypass (Engage) and Boost. 

 

It’s slightly richer sounding than the Tube side of my Keeley Tube Drive, and a little more expansive. While its Voice / Tilt EQ Control is rather subtle overall.

 

Essentially the Bypass / First Footswitch delivers a Clean Channel, and the Boost Footswitch engages a more Overdriven / Saturated gain stage.

 

Controls - Level, Tone, Drive, Voice (Tilt EQ / Tightness), Bypass = Clean Channel Engage, Boost = Overdrive Channel / More Saturation. 

 

As mentioned, the 2 Footswitches work additively rather than as separate Channels - so more of a Clean Tube action then with further gain saturation!

 

The VOICE and DRIVE controls are placed after the Triode Gain Stage and ahead of Pentode Clipping Stage, with TONE and LEVEL after, offering a wide range of tone shaping!

2026-GPX-Hagerman-Vulture-Skull-Insides-700.jpg

Everything was pretty clear and intuitive for me right from the start, while the subtle nature of the Voice control confused me a little initially. I could sense that when maxed out - it delivered a tighter output, but I wasn't clear what mechanical function it was serving at the time.

 

Jim explained it to me as follows - "VOICE is a tilt-style tone control, very similar to TONE, but placed ahead of the clipping tube (TONE comes after). At noon it has a slight dip at about 500Hz.  With the BOOST mode engaged, its ground gets lifted and it doesn't do very much.  Probably best cranked when in this mode, however, to give you a tighter sound."

 

He then added - "DRIVE is only there is you want to get clean, warm tones (for example ahead of a digital rig). Personally I always leave it cranked.

 

Preferred settings - Level @ 3 o'c, Tone @ Noon, Drive @ Max, Voice @ Max - and then two stages via Bypass and Boost Footswitches - the latter which adds significant saturation.

 

If I compare the Vulture Skull to my Keeley Tube Drive - the Vulture offers a little more range than the Keeley on the Tube side, but can't compete with the combined gain of Keeley's Tube + Super Phat Mod Channel Output - those together can deliver relatively high gain output, while the Vulture Skull is overall a little more tempered at Mid Gain. When just comparing the tube sides - the Vulture Skull is a touch more potent than the Keeley Tube side.

 

Generally I'm a fan of full fat textures and tones, and tend to like things relatively saturated for maximum harmonic output. Which is how I set this pedal. My preferred settings deliver the best combination of harmonic richness and saturation, with a sort of 2-stage action - which is accurately labelled as 'Boost' in terms of how that hits!

2026-GPX-Hagerman-Vulture-Skull-Diagonal-700.jpg

Due to the scarcity of this style of TV 1/2 Triode / 1/2 Pentode Tube, Jim uses a variety of 6*8*, and 6**8* Tubes - which all sound incredible - warm and rich as I've said many times here.

 

The Vulture Skull Tube Overdrive is essentially a Halloween Release - which goes for $289 on Hagerman Webstore. It's a fantastic 2-stage Tube Overdrive which sounds exceptional in my rig, and pairs particularly well with the recently arrived Martian Sound Cydonia Germanium Harmonic Multiplier. When running that combination you don't need a Tube Amp - that beautifully delivers Tube Amp dynamics - which you can then further ramp up via stacking with other complementary pedals - like indeed the Cydonia!

 

This is a fantastic expansive Tube Overdrive take that comes highly recommended. If you want to warm up and add saturation to a mostly solid-state or digital pedal rig - it is the perfect vehicle for giving you those tube dynamics and feel. It's one of three Tube Overdrives I currently have on my board - alongside the Crazy Tube Circuits Venus, and Keeley Tube Drive Dealer Edition. All three sound phenomenal, all 3 are tonally and texturally distinct. I would not want to be without any one of them. The Hagerman Vulture Skull is incredibly versatile in its application - it really enhanced the tone and texture of my overall rig. And it's been really smartly engineered for easy running. The Tube doesn't get hot, and it gets by on just 9V @ 380mA - so all should be able to easily deploy it.

 

Tube Overdrives have really come into their own of late - in being able to run off 9V supplies at a relatively low current. It used to be that Tube Overdrives needed 12 or 18V at fairly high levels of amperes - which made for some power supply complexities. That is now no longer the case. And these amazing tube amp like devices are now available to all. It's well worth your while to get onboard this particular train!

2026-GPX-Hagerman-Vulture-Skull-Tube-Guard-700.jpg

When I received the pedal I was a little surprised that it didn't have some kind of tube guard / shroud / shield in place to protect said tube from accidents and incidents. I personally do have the occasional clumsy day, and worry that I might drop or knock something over that could damage or harm the tube in some manner. To which ends I spent a couple of hours brainstorming how I might best be able to provide some kind of protection for said tube.

 

I was looking on Amazon.co.uk/com for anything that could shield the tube in some manner - when I finally landed on this Reinmoson 304 Stainless Steel Ultra Fine Mesh Tea Infuser (1.5”x2.2” / 8mmL x 38mmW x 56mmH). Note that I had to bend / deform it very slightly - so that its aperture became slightly more oval - to fit in precisely between the knobs. You just screw its lid off and use the body portion as a cover for the tube - it actually fits really well after that slight adjustment, and just sits there and provides the perfect incidental protection.

 

It may not be entirely necessary but it provides me with peace of mind, and delivers significant protection for the tube! There's about 1/2 a millimetre play /  movement where it's mostly pretty snug against that outer rubber ring!

2026-GPX-Hagerman-Vulture-Skull-Main-700.jpg

Demos

Stefan Karlsson
Posted by Stefan Karlsson
PopularCommentsRSS FeedContent Alerts
Share to TwitterShare to Facebook
Add New Comment
You must be registered and logged in to comment
Content Alerts
Sign Up
News Navigation






















































Stefan Karlsson
3 mostly Brian May inspired Mini Pedals from Japan's Brian May experts Kz Guitar Works
"There's bound to be significant difference - the "...
6 days ago
Stefan Karlsson
3 mostly Brian May inspired Mini Pedals from Japan's Brian May experts Kz Guitar Works
"Hey Mik - I'm not really in a position to say "...
6 days ago
Mik Jay
3 mostly Brian May inspired Mini Pedals from Japan's Brian May experts Kz Guitar Works
"I realize this might be a bit early to ask but "...
7 days ago
Stefan Karlsson
House Music Label Odyssey - My DJ'ing Years : 1988-2008
"Thank you Troy - Music has always been a very big "...
7 days ago
Troy X
House Music Label Odyssey - My DJ'ing Years : 1988-2008
"Great article Stefan, I love all this stuff too, "...
7 days ago
Waiting